How to Remove Windows Bug using Command Mode

View Of The Screen Infected With Windows Bug

Windows updates are benefited grace for us by Microsoft, but there are times during updates we're encountering problem of windows 7, 8, and 10 versions because of the windows bug. There are common factors why this happen, one of the most common is using the pirated software. Mostly in Personal Computer or PC. Because the laptop is pre-installed during buying on it.

If we're enjoying the new update features of Microsoft but other also is struggling of their computer running smoothly. Because of the Windows bug error called KB3189866. Which causes freezes of the windows operating system. Full information and repair in this link: How to fix KB3189866 update bug on Windows 10?

USING COMMAND MODE TO FIX OTHER WINDOWS BUG- one of the bug cause problem is kb2565062, here are how to remove this bug. See images posted here to help you.

1. REMOVE THE UPDATES USING YOUR CONTROL PANEL

1. Click start button, then click control panel.
2. Once your in control panel, click icon called uninstall program in program menu.
3. Then click view installed updates.
4. Once it viewed right click on the updates.
5. Then click uninstall.

2. COMMAND MODE TO REMOVE COMPLETELY THE BUG

1. Open the MSDOS of your computer, click start button, then in search bar type CMD.
2. Once you see the icon called command prompt, click on it.
3. Once the black screen pop-up, you will see the command line.
4. Type in the blinking keyboard cursor, the command stated in the image above here, like SLMGR-REARM if this command will not work, use this other command SLMGR /REARM. see the image below here:
5. Click enter key.
6. Once you see the instruction to restart your windows to take effect. Restart your computer now.

Once you go back in your desktop you can setup again your desktop properties like desktop background and screen saver. Here are other information about the software counterfeit: What Is Software Counterfeit Error In Desktop 

5 Ideas How to Speedup Internet Connections

If you have experienced a low signal on your internet, it is understood that your internet signal is strangulated, either the cause of settings or through other applications stored in history. Or either cause of one of the programs stored in your computer disk, like a virus scanner stored in system 32. 

Feel lucky if you read this post, we're encountered the same problem before. And found these commands and solve my problem before, you need only a basic application of the computer and use the command mode or CMD on your computer.

1. HOW TO OPEN COMMAND MODE OF YOUR PC USING WINDOWS 7, 8, AND 10

1. Open your computer, and on your desktop, click the start button below the left side.
2. When you see the search bar, type inside on it CMD.
3. When you find it right-click on it and click "Run as administrator" and click yes in a pop-up window.
4. Dark windows will appear or an MS-DOS command line. 

2. IN YOUR COMMAND LINE OR MS-DOS

Type this in blinking keyboard cursor

netsh int ipv4 reset

netsh int ipv6 reset

netsh winsock reset

ipconfig /flushdns

netsh int IP reset c:\resetlog.txt

or use ping -t and type the IP address of your router, for example, 192.168.1.1

3. DISABLE AND ENABLE INTERNET ADAPTER IN YOUR COMPUTER

1. Right Click on the monitor icon of your notification area, it is right side down of your screen.
2. A window will display, look on the left side of the screen to find the menu called. "Change Adapter Settings"
3. The other window right-click in the "Local Area Connections"
4. Then click disable, then after a few seconds when your internet is disabled, right-click again and click enable.

4. REMOVE OLD VIRUS SCANNER FILE THAT BLOCKING YOUR ADAPTER DRIVER

1. Maybe you installed before the AVG antivirus, then a file that may be not removed during uninstall that cause the internet speed low.
2. Open your My Computer Icon.
3. Double click in drive c:
4. And double click folders windows\system32\drivers
5. And try to delete this driver called "avgfwd6a.sys"

5. CHANGE THE SETTINGS OF IPV4 OR IPV6 SETTINGS

1. Right Click on the monitor icon of your notification area, it is right side down of your screen.
2. A window will display, look on the left side of the screen to find the menu called. "Change Adapter Settings".
3. The other window right-clicks in the "Local Area Connections".
4. Click properties.
5. Click ipv4 or ipv6 and click the properties button.
6. Then set the "obtain an IP address automatically".
7. Click the ok button.

Likewise, you can run virus scanning of your computer for spam and viruses like a trojan. Also, you can run sfc /scannow using command mode to check any bad files or corrupt that will cause a hangup of your system. Also the firewall services and create a system restore so that you can restore your windows if ever there are bad causes happen on your computer.